Armonìa Official Releases

– New features –

* DMD Support for Nota
Nota can now be integrated into Dynamic Music Distribution (AES67-only) systems alongside amplifiers such as Mezzo A+, Duecanali and Quattrocanali Series DSP+.
(Nota firmware 1.2.4 is required)

* Speaker Impedance Verification in Health+
Unica Series amplifiers can now measure reference and validation loudspeaker impedance curves in Health+. Validation curves are compared against their reference to assess transducers performance over time, helping users identify degradation or faults early.
(Unica firmware 1.12.0.840 is required)

* Amplifier Discovery from Design/Add
In addition to Design/Match, users can now discover and add online amplifiers directly from the Design/Add > Amplifier modal window, streamlining the workflow when adding online devices to a project.

* New File Formats
ArmoníaPlus introduces updated file formats across the board (e.g., .pam -> .pam2, .paw3 -> .paw4) for improved compatibility and future extensibility. The new format significantly boosts performance on large systems, for instance: saving a .paw4 project with 90 amplifiers now takes approximately 5 seconds compared to 20 seconds with the previous .paw3 format, up to a 300% improvement.

– Bug fixes and minor improvements –

* Minor fixes and performance improvements

– Firmware bundled with the release –

* Unica & Unica T: 1.12.0 (new)
* Nota: 1.2.4 (new)
* Mezzo Series: 1.6.1
* T Series: 1.12.0
* X Series: 1.12.0
* Ottocanali, Quattrocanali and Duecanali DSP Series: 1.12.0 (new)
* Quattrocanali: 2.0.2
* Dsp4: 1.6.28
* IPAL, MDrive: 1.8.6
* WallMount Touch: 1.3.1
* PC ViewsHost: 3.1
* Verso: 1.0.1

– Bug fixes and minor improvements –

* Fixed a bug from 2.8.0 that could cause a crash when a zone or a source is selected in CH Strip Workspace page.

– Firmware bundled with the release –

* Unica & Unica T: 1.12.0
* Mezzo Series: 1.6.1 (New)
* T Series: 1.12.0
* X Series: 1.12.0
* Ottocanali, Quattrocanali and Duecanali DSP Series: 1.12.0
* Quattrocanali: 2.0.2
* Dsp4: 1.6.28
* IPAL, MDrive: 1.8.6
* WallMount Touch: 1.3.1
* PC ViewsHost: 3.1
* Verso: 1.0.1 (New)

– Bug fixes and minor improvements –

* Fixed a bug from 2.8.1 that could set incorrect filter values when two different snapshots were reloaded from the amplifier with Armonía connected.

– Firmware bundled with the release –

* Unica & Unica T: 1.12.0
* Mezzo Series: 1.6.1 (New)
* T Series: 1.12.0
* X Series: 1.12.0
* Ottocanali, Quattrocanali and Duecanali DSP Series: 1.12.0
* Quattrocanali: 2.0.2
* Dsp4: 1.6.28
* IPAL, MDrive: 1.8.6
* WallMount Touch: 1.3.1
* PC ViewsHost: 3.1
* Verso: 1.0.1 (New)

– New features –

* EQ A/B Comparison
Users can now easily compare two equalization options with the new EQ A/B feature, enabling quick evaluation and fine-tuning of different EQ settings without losing context.

* Introduction of DC Rider Amplifiers
Support for the new DC Rider series, available in both 8-channel and 16-channel configurations.

* Support for Nota Amplifier
Users can now configure and deploy the new Nota PoE amplifier.

* Matrix Page Redesign
The matrix pages have been restyled to improve usability and support larger channel counts.

– Bug fixes and minor improvements –

* Fixed an rare issue where importing an EQ layer with a high number of filters could occasionally result in incorrect applying of filter parameters

* Any speaker mute status is now correctly shown on all the workspace pages

* Mute/solo rubberband is now correctly shown even if nothing is selected

* Standby status is now shown clearly in Config>Mains page

* Minor fixes and performance improvements

– Firmware bundled with the release –

* Unica & Unica T: 1.12.0
* Mezzo Series: 1.6.1 (New)
* T Series: 1.12.0
* X Series: 1.12.0
* Ottocanali, Quattrocanali and Duecanali DSP Series: 1.12.0
* Quattrocanali: 2.0.2
* Dsp4: 1.6.28
* IPAL, MDrive: 1.8.6
* WallMount Touch: 1.3.1
* PC ViewsHost: 3.1
* Verso: 1.0.1 (New)

– New features –

* Introduction of Unica 8T and Unica 4T Devices

* Users can now deploy and configure the new Unica 8T and Unica 4T amplifiers.

* Enhanced Group Assignment for Faster System Visualization
When a speaker is selected, the associated group names are highlighted in blue, making it quicker to verify assignments and navigate between elements in the system.

* More Control from the Speaker’s Perspective
The Advanced EQ page now provides deeper insights into each speaker’s configuration, including the speaker name, preset details, and a new tab for each assigned group. Users can view the total filter count for each group and quickly navigate to the group’s EQ main page.

* Improved Device Selection & Power Management
A new “Select All” & “Select None” right-click menu function simplifies device selection in the workspace. These selections work seamlessly with an updated bottom-bar “Config/Mains” control, enabling users to quickly power devices on/off or manage eco-mode settings without leaving the workspace.

* “Replace With”
The new right-click “Replace With …” function allows a faulty device to be swapped with a new one without manual reconfiguration. The new device inherits all DSP, network, and Dante settings from the replaced unit, simplifying maintenance.

* Display Read-Only Mode for Unica Series
To enhance security, users can enable a Display Read-Only Mode on Unica amplifiers, restricting certain operations (e.g., muting/unmuting channels) in unattended or public-facing systems.

* Config/Preset Enhancements
Preset selection is now more intuitive, displaying the applied preset application directly on speakers. Users can also edit preset Application and Manufacturer’s EQ categories across multiple speakers simultaneously, even if model is not matching exactly, provided they share the same configuration options.

* Config/Network – Expanded Network Configuration Options
Formerly “Config/IP,” the new Config/Network section allows users to configure port modes (Switched, Split, etc.) and assign IP addresses across all Ethernet ports on multiple amplifiers, not just the control port.

* Channel Strip Mode & Workflow Simplification
Multiple tuning functions (Gain, Mute, EQ, Delay, Polarity) are unified into the new Channel Strip Mode for faster, more intuitive adjustments.

* Mute / Solo
Mute and Solo pages have been merged into Mute/Solo. Solo mode can now be used in Exlclusive or Additive mode, allowing users to check speakers individually or in combination.

* Workflow Simplification
The “Show” step has been removed, and impedance monitoring has been relocated to the now simplified “Tune” step.

– Bug fixes –

* Improved Networking stability

* Minor fixes and performance improvements

– Firmware bundled with the release –

* Unica T: 1.12.0
* Unica: 1.12.0
* Mezzo Series: 1.6.0
* T Series: 1.12.0
* X Series: 1.12.0
* Ottocanali, Quattrocanali and Duecanali DSP Series: 1.12.0
* Quattrocanali: 2.0.2
* Dsp4: 1.6.28
* IPAL, MDrive: 1.8.6
* WallMount Touch: 1.3.0
* PC ViewsHost: 3.0
* Verso: 1.0.0

– New features –
* Adds support to Verso, allowing X, T, Mezzo, and Canali Series devices to be part of MyUniverso
* Improves alarms and status handling for all MyUniverso-supported devices
* Adds support to DMD (Dynamic Music Distribution) for Unica Series
* Adds support to AES67 Raw SDP and Dolby Atmos Connect patching on Duecanali DSP+, Quattrocanali DSP+ and Mezzo A+

– Bug fixes –
* Improved Networking stability
* Minor fixes and performance improvements

– Firmware bundled with the release –
* Unica Series: 1.12.0 (New)
* Mezzo Series: 1.6.0 (New)
* T Series: 1.12.0 (New)
* X Series: 1.12.0 (New)
* X4 L: 1.12.0 (New)
* Ottocanali, Quattrocanali and Duecanali DSP Series: 1.12.0 (New)
* Quattrocanali: 2.0.2
* Dsp4: 1.6.28
* IPAL, MDrive: 1.8.6
* WallMount Touch: 1.3.0 (New)
* PC ViewsHost: 3.0 (New)
* Verso: 1.0.0 (New)

– Bug fixes –

* Fix possible crash if a previous version was not unistalled properly

* Fix ‘Error reconnecting’ while synchronizing devices from a saved system

* Bug fixes and performance improvements have been added.

– Firmware bundled with the release –

* Unica Series: 1.11.1 (New)

* Mezzo Series: 1.5.2

* T Series: 1.11.0

* X Series: 1.11.0

* X4 L: 1.11.0

* Ottocanali, Quattrocanali and Duecanali DSP Series: 1.11.0

* Quattrocanali: 2.0.2

* Dsp4: 1.6.28

* IPAL, MDrive: 1.8.6

* WallMount Touch: 1.2.1

* PC ViewsHost: 2.1

* Bug fixes and performance improvements have been added.

– Firmware bundled with the release –

* Unica Series: 1.11.0 (New)

* Mezzo Series: 1.5.2

* T Series: 1.11.0

* X Series: 1.11.0

* X4 L: 1.11.0

* Ottocanali, Quattrocanali and Duecanali DSP Series: 1.11.0

* Quattrocanali: 2.0.2

* Dsp4: 1.6.28

* IPAL, MDrive: 1.8.6

* WallMount Touch: 1.2.1

* PC ViewsHost: 2.1

– New features –

* The new Unica Series amplifier models now supports Live Impedance.

* Added support to port configuration change on Mezzo A+

– Bug fixes –

* Bug fixes and performance improvements have been added.

– Firmware bundled with the release –

* Unica Series: 1.11.0 (New)

* Mezzo Series: 1.5.2

* T Series: 1.11.0

* X Series: 1.11.0

* X4 L: 1.11.0

* Ottocanali, Quattrocanali and Duecanali DSP Series: 1.11.0

* Quattrocanali: 2.0.2

* Dsp4: 1.6.28

* IPAL, MDrive: 1.8.6

* WallMount Touch: 1.2.1

* PC ViewsHost: 2.1

– New features –

* The new Unica Series amplifier models are now supported.
Users can now design systems using the new Unica amplifier models, which offer unique features including configurable GPIO, PoE input for mains-less configuration.

* Streamlined Remote-Monitoring with ArmoníaPlus and Universo.
ArmoníaPlus now offers streamlined remote-monitoring capabilities by transforming projects into remote-monitored systems (Sites) in the Universo cloud-based platform. With the user-friendly ArmoníaPlus interface, users can easily enable, navigate, edit, and disable Universo settings for each project, allowing remote monitoring from any device, anywhere in the world.

* Interactive tuning’s support for Smaart v9.
Users can now benefit from the integrated system design and verification workflow of ArmoníaPlus’ Interactive Tuning functionality along with the latest version 9 of Smaart by Rational Acoustics.

* Amplifier’s settings page redesign.
Redesigned amplifier settings page with a new and improved interface for configuring network settings, Dante settings, and additional family-specific parameters such as GPIO in Unica Series and the Wi-Fi module in X Series.

– Bug fixes –

* Bug fixes and performance improvements have been added.

– Firmware bundled with the release –

* Unica Series: 1.11.0 (New)

* Mezzo Series: 1.5.2 (New)

* T Series: 1.11.0 (New)

* X Series: 1.11.0 (New)

* X4 L: 1.11.0 (New)

* Ottocanali, Quattrocanali and Duecanali DSP Series: 1.11.0 (New)

* Quattrocanali: 2.0.2

* Dsp4: 1.6.28

* IPAL, MDrive: 1.8.6

* WallMount Touch: 1.2.1

* PC ViewsHost: 2.1

– Bug fixes –

* Fixed a bug where projects created with version 1.4 (or below) could not be saved.

* Fixed a crash that could happen on startup when an unexpected network adapter configuration is found.

* Fixed a bug that prevents zones or sub-zones to be selected in ViewsDesigner.

* Fixed a bug that prevents devices without a digital output to be listed while patching a stereo mono-mix source.

* Fixed a bug where workspace zoom levels wehre not reset to 100% on new project.

– Firmware bundled with the release –

* Mezzo Series: 1.5.2

* T Series: 1.11.0

* X Series: 1.11.0

* X4 L: 1.11.0

* Ottocanali, Quattrocanali and Duecanali DSP Series: 1.11.0

* Quattrocanali: 2.0.2

* Dsp4: 1.6.28

* IPAL, MDrive: 1.8.6

* WallMount Touch: 1.2.1

* PC ViewsHost: 2.1

– Bug fixes –

* Fixed a bug where projects created with version 2.4 (or below) containing high-impedance loudspeakers could not be saved.

* Fixed a crash occurring during software startup due to inconsistencies in the software installation folders.

* Bug fixes and performance improvements have been added.

– Firmware bundled with the release –

* Mezzo Series: 1.5.2

* T Series: 1.11.0

* X Series: 1.11.0

* X4 L: 1.11.0

* Ottocanali, Quattrocanali and Duecanali DSP Series: 1.11.0

* Quattrocanali: 2.0.2

* Dsp4: 1.6.28

* IPAL, MDrive: 1.8.6

* WallMount Touch: 1.2.1

* PC ViewsHost: 2.1

– New features –

* The new Mezzo A+ amplifier models are now supported.
Users can design systems with the new Mezzo A+ models and conveniently patch the AES67 inputs to AES67 flows from within ArmoníaPlus.

* DMD now support both Mezzo A+ and Duecanali/Quattrocanali DSP+ models.

* New AES67 format for DMD sources.
Users can configure sources to receive an AES67 stream.

* New Priority Input feature for DMD systems.
Users can now add a new control object to DMD systems. The Priority Input object allows the user to configure a GPI to play a specific input to one or more zone by applying a differential voltage or closing a contact.

* New embedded-speaker-preset-library release method.
Users can now receive new or updated loudspeaker presets automatically upon release by Powersoft.

– Bug fixes –

* Bug fixes and performance improvements have been added.

– Firmware bundled with the release –

* Mezzo Series: 1.5.2 (New)

* T Series: 1.11.0

* X Series: 1.11.0

* X4 L: 1.11.0

* Ottocanali, Quattrocanali and Duecanali DSP Series: 1.11.0

* Quattrocanali: 2.0.2

* Dsp4: 1.6.28

* IPAL, MDrive: 1.8.6

* WallMount Touch: 1.2.1 (New)

* PC ViewsHost: 2.1 (New)

– New features –

* The new Duecanali and Quattrocanali DSP+ amplifier models are now supported.

* New AES67 input patch feature for DSP+ amplifier models.
Users can conveniently patch the AES67 inputs of Duecanali and Quattrocanali DSP+ models to AES67 flows from within ArmoníaPlus.

– Bug fixes –

* Bug fixes and performance improvements have been added.

– Firmware bundled with the release –

* Mezzo Series: 1.5.0

* T Series: 1.11.0

* X Series: 1.11.0

* X4 L: 1.11.0

* Ottocanali, Quattrocanali and Duecanali DSP Series: 1.11.0

* Quattrocanali: 2.0.2

* Dsp4: 1.6.28

* IPAL, MDrive: 1.8.6

* WallMount Touch: 1.2.0

* PC ViewsHost: 2.0

* Fixes a bug that caused ArmonìaPlus to unexpectedly crash when performing device discovery operations.

* Fixes a bug that caused some devices to mistakenly present the status �Error reconnecting�.

* Fixes a bug in which applied network settings would be automatically reset in some instances.

– Bug fixes
* Bug fixes and performance improvements have been added.

– Firmware bundled with the release –

* Mezzo Series: 1.4.0 (New)

* T Series: 1.10.0

* X Series: 1.10.0

* X4 L: 1.10.0

* Ottocanali, Quattrocanali and Duecanali DSP+D: 1.10.0

* Quattrocanali: 2.0.2.48

* Dsp4: 1.6.27.0

* IPAL, MDrive: 1.8.6

* WallMount Touch: 1.1.1 (New)

* PC ViewsHost: 1.5.2 (New)

* New Cloud Integration
Users can now save projects in the Cloud, invite other users to collaborate on specific projects and store a project version history.

* New Mono-Mix Sources
All Mezzo AD models now support Dante sharing of stereo sources as mono mixes.

* New WM Touch Network recovery!
Users can now configure the IP address of a WM Touch from ArmoníaPlus, even if it’s set in a different subnet.

* New Dante Flows Warnings
ArmoníaPlus will display a warning when users are designing a system that potentially exceeds the maximum number of Dante flows supported by Mezzo amplifiers (as per datasheet specs).

* New Dante Fanout Warnings
ArmoníaPlus will display a warning inviting users to set their Dante sources to multicast when they are designing a system that may potentially generate Dante fanout conditions.

* New SNMP implementation
Powersoft amplifiers now support SNMP network monitoring, allowing the user to read critical and essential information about the status of amplifiers and their operating conditions. Access the Download area of My Powersoft for more information.

– Bug fixes
* Bug fixes and performance improvements have been added.

– Firmware bundled with the release –

* Mezzo Series: 1.4.0 (New)

* T Series: 1.10.0

* X Series: 1.10.0

* X4 L: 1.10.0

* Ottocanali, Quattrocanali and Duecanali DSP+D: 1.10.0

* Quattrocanali: 2.0.2.48

* Dsp4: 1.6.27.0

* IPAL, MDrive: 1.8.6

* WallMount Touch: 1.1.1 (New)

* PC ViewsHost: 1.5.2 (New)

* Dante integration: it is possible to patch the input to Dante sources directly from Armonía
* Dante integration: Dante transmitter labels can be edited directly from the device Dante details
* Dante integration: Add dante routing pick points “Out Voltage”, “Out Current” and “Physical IN”
* Completely revisited system list
* Add option to filter speaker preset when adding a new speaker to workspace
* Add support to line out configuration on Mezzo 2ch
* Add support to Rational Acoustic SmaartDi in interactive tuning
* Add advanced settings in workspace notes
* Improve workspace background options
* Add support to VPN to access and control your system remotely
* Add support for Mezzo and Quattrocanali in Health+ mains page
* Graphical restyle of data tables all around Armonía
* Update speaker preset library

* Minor bug fixes and stability improvements

– Firmware bundled with the release –

* Mezzo Series: 1.1.0

* T Series: 1.9.0

* X Series: 1.9.0

* X4 L: 1.9.0

* Ottocanali, Quattrocanali and Duecanali DSP+D: 1.9.0

* Quattrocanali: 2.0.2.48

* Dsp4: 1.6.27.0

* Add support for Mezzo product family
* Add HealthPlus for managing system status

* Minor bug fixes and stability improvements

* Update speaker preset library
If you are using L’Acoustics presets please check the updated list, because some have been removed

– Firmware bundled with the release –

* Mezzo Series: 1.0.0.88

* T Series: 1.8.7.16
Now supporting new speaker preset 3 format

* X Series: 1.8.7.16
Now supporting new speaker preset 3 format

* X4 L: 1.8.7.16
Now supporting new speaker preset 3 format

* Ottocanali, Quattrocanali and Duecanali DSP+D: 1.8.7.16

* Quattrocanali: 2.0.2.22

* Dsp4:1.6.25.0

* Completely revised amplifier’s details user interface: now it’s easier to access all the amplifier’s processing block
* Add control of Dante settings right from the amplifier details
* Add new speaker preset v3 format including manufacturer eq and other parameters
* Add sub harmonics generator for particular speaker preset (currently only for Powersoft Mover)
* Add Market place giving easy access to third party models (speaker and amplifiers)
* Add support to DspLite E
* Extended support for some workspace functionalities to some legacy devices (M-Series, Dsp modules)
* Better management of devices not having internal signal generator in workspace testSystem

* Minor bug fixes and stability improvements

* Update speaker preset library
If you are using L’Acoustics presets please check the updated list, because some have been removed

WARNING: a firmware update is required to control X-Series, Ottocanali DSP+D, Quattrocanali DSP+D, T-Series, Loto. The requested firmware is bundled within this version.

– Firmware bundled with the release –

* T Series: 1.8.7.x (New)
Now supporting new speaker preset 3 format

* X Series: 1.8.7.x (New)
Now supporting new speaker preset 3 format

* X4 L: 1.8.7.x (New)
Now supporting new speaker preset 3 format

* Ottocanali, Quattrocanali and Duecanali DSP+D: 1.8.7.x

* Quattrocanali: 2.0.2.22

* Dsp4:1.6.25.0

– Bug fixes
* ArmoníaPlus freeze when working on models without Dante sources (X Series, Ottocanali DSP+D) with speaker presets.
* Crash when a device reset is issued from the amplifier Webapp while the advanced equalizer window is open and assigned to a group.
* ArmoníaPlus freeze when reloading speaker preset library if you have two or more amplifier open in the speaker library section

– Improvements
* Update italian translation.

– Firmware bundled with the release –

* T Series: 1.8.6.250

* X Series: 1.8.6.160 (New)
Slightly change the power supply secure operating area limiter to improve the amplifier safety when working in stressfull conditions

* X4 L: 1.8.6.322 (New)
First version supporting the new model

* Ottocanali, Quattrocanali and Duecanali DSP+D: 1.8.6.140

* Quattrocanali: 2.0.2.22

* Dsp4:1.6.25.0